TorqFix

5008 / 3008 DV6 ancillary drive belt - Start & Stop — PEUGEOT

5008 / 3008 DV6 ancillary drive belt - Start & Stop on Peugeot: 33 steps, engines DV6C(9HD), DV6C(9HR).

Workshop procedure for PEUGEOT — the exact step sequence and torque figures, straight from real workshop data.

33 steps 2 engine codes

🧭 Before you start

Fits: platform codes 1.6, HDIF

  • Timing position: the crankshaft or camshaft is set and locked during this job
  • Special tools named: locking tool

🔧 Engine codes this applies to

DV6C(9HD)DV6C(9HR)

📐 33 workshop diagrams for DV6C(9HD)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 1
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 2
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 3
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 4
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 5
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 6
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 7
5008 / 3008 DV6 ancillary drive belt - Start & Stop — DV6C(9HD) · diagram 8
+ 25 more diagrams
🔒 33 workshop diagrams for this job Ask about your Peugeot DV6C(9HD) — free or sign up free to see the drawings

📋 Procedure

Preparation and removal

  1. Disconnect the battery
  2. Wrench:
  3. Remove the front right wheel
  4. Remove the right wheel arch front section
  5. Remove the power steering line mount
DV6C(9HD)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Place the power steering lines aside
  2. Remove the bolt
  3. Remove the nut
  4. Remove the bolts
  5. Remove the nuts
  6. Remove the subframe front right tie rod
  7. Remove the covers

Installation and checks

  1. Turn the upper tensioner clockwise
  2. Use the special tool
  3. Fit the tensioner locking tool
  4. Turn the lower tensioner clockwise
  5. Use the special tool
  6. Remove the tensioner locking tool
  7. Turn the upper tensioner clockwise
  8. Use the special tool
  9. Remove the tensioner locking tool
  10. Note: Check the alignment
  11. Refit all other parts in the reverse order of removal
  12. Reconnect the battery
Workshop diagrams

Ask TorqFix about your Peugeot DV6C(9HD) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Peugeot DV6C(9HD) — free → or sign up free to see the drawings

Other PEUGEOT procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.