TorqFix

Gearbox removal & installation: Peugeot 206, MA (DV4C)

Step-by-step gearbox removal & installation for the Peugeot 206, MA (DV4C): 40 steps. What to remove, in what order, and what to check after.

Workshop procedure for PEUGEOT — the exact step sequence and torque figures, straight from real workshop data.

40 steps 1 engine code

🧭 Before you start

Fits: platform codes 1.4, HDIF

  • Opens: gearbox oil

Don't miss

  • Remove the starter motor but do not disconnect

🔧 Engine codes this applies to

DV4C(8HR)

📐 30 workshop diagrams for DV4C(8HR)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

206+ MA (DV4C engine) — DV4C(8HR) · diagram 1
206+ MA (DV4C engine) — DV4C(8HR) · diagram 2
206+ MA (DV4C engine) — DV4C(8HR) · diagram 3
206+ MA (DV4C engine) — DV4C(8HR) · diagram 4
206+ MA (DV4C engine) — DV4C(8HR) · diagram 5
206+ MA (DV4C engine) — DV4C(8HR) · diagram 6
206+ MA (DV4C engine) — DV4C(8HR) · diagram 7
206+ MA (DV4C engine) — DV4C(8HR) · diagram 8
+ 22 more diagrams
🔒 30 workshop diagrams for this job Ask about your Peugeot DV4C(8HR) — free or sign up free to see the drawings

📋 Procedure

  1. Disconnect the battery
  2. Gearbox support to body:
  3. Gearbox support to gearbox:
  4. Ball joint splitting tool:
  5. Gearbox supports:
DV4C(8HR)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Remove the engine lower cover
  2. Disconnect the clutch cable from the release lever on the gearbox
  3. Disconnect the clutch cable from the bracket and release lever
  4. Remove the power steering hose brackets
  5. Disconnect the gearbox earth cables
  6. Disconnect the reversing light switch
  7. Disconnect the preheating unit
  8. Disconnect the gearbox operating linkage from the gearbox
  9. Use a special tool:
  10. Remove the front wheels
  11. Remove the left wheel arch liner
  12. Drain the gearbox oil
  13. Remove the drive shafts
  14. Remove the exhaust pipe
  15. Remove the reaction link
  16. Remove the starter motor but do not disconnect
  17. Remove the power steering pump
  18. Loosen the engine/gearbox attaching bolts
  19. Support the engine/gearbox with a lifting jack
  20. Use a hoist to support the gearbox
  21. Remove the gearbox support
  22. Use a special tool:
  23. Lower the engine/gearbox slightly
  24. Remove the gearbox support bracket
  25. Remove the engine/gearbox attaching bolts
  26. Remove the gearbox
Workshop diagrams

Ask TorqFix about your Peugeot DV4C(8HR) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Peugeot DV4C(8HR) — free → or sign up free to see the drawings

Other PEUGEOT procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.