TorqFix

Single plate clutch with OM602 (602.980)/984/985 engine — MERCEDES-BENZ

Single plate clutch with OM602 (602.980)/984/985 engine on Mercedes-Benz: 29 steps, engines 602.980, OM602.9, OM602.984.

Workshop procedure for MERCEDES-BENZ — the exact step sequence and torque figures, straight from real workshop data.

29 steps 3 engine codes

🧭 Before you start

Fits: platform codes 210, D, |, 212, 310, 312, 410, 412, 512, 612, 812, O

  • Renewed: if necessary note, oil seals, drive shaft seals

Don't miss

  • We recommend that the clutch release bearing should always be renewed
  • Do not bring any grease into contact with the clutch plate(s) facing, clutch pressure plate surface or flywheel surface
  • Always renew the concentric slave cylinder
  • While tightening ensure that the centering drift can be moved easily
  • Do not bring any grease into contact with the clutch plate facing, clutch cover surface or flywheel surface

🔧 Engine codes this applies to

602.980OM602.9OM602.984

📐 4 workshop diagrams for 602.980

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

Single plate clutch with OM602 (602.980)/984/985 engine — 602.980 · diagram 1
Single plate clutch with OM602 (602.980)/984/985 engine — 602.980 · diagram 2
Single plate clutch with OM602 (602.980)/984/985 engine — 602.980 · diagram 3
Single plate clutch with OM602 (602.980)/984/985 engine — 602.980 · diagram 4
🔒 4 workshop diagrams for this job Ask about your Mercedes-Benz 602.980 — free or sign up free to see the drawings

📋 Procedure

  1. Centering tool:
  2. Use a special tool:
  3. Loosen the bolts in several stages, in a criss-cross pattern
  4. Grease the thrust bearing inner bore, drive plate splines and release fork pivot points
  5. We recommend that the clutch release bearing should always be renewed
602.980? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Check the clutch release bearing guide tube and fork; renew if necessary
  2. Note: Do not bring any grease into contact with the clutch plate(s) facing, clutch pressure plate surface or flywheel surface
  3. Note: Always renew the concentric slave cylinder
  4. Note: While tightening ensure that the centering drift can be moved easily
  5. Remove the alignment tool
  6. Refit the gearbox
  7. Check the flywheel friction surface for condition and wear
  8. Grease the thrust bearing inner bore, drive plate splines and release fork pivot points
  9. Note: Do not bring any grease into contact with the clutch plate facing, clutch cover surface or flywheel surface
  10. Renew the oil seals if necessary
  11. Always renew the drive shaft seals
Workshop diagrams

Ask TorqFix about your Mercedes-Benz 602.980 — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Mercedes-Benz 602.980 — free → or sign up free to see the drawings

Other MERCEDES-BENZ procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.