TorqFix

DS5 - DV6C — CITROEN

DS5 - DV6C on Citroen: 63 steps, engines DV6C(9HD), DV6C(9HR). What to remove, in what order, and what to check after.

Workshop procedure for CITROEN — the exact step sequence and torque figures, straight from real workshop data.

63 steps 2 engine codes

🧭 Before you start

Fits: platform codes 1.6, HDI, |, 110

Don't miss

  • Caution! The temperature of the engine and exhaust will increase significantly
  • Do not re-use the drained fluid or fluid from opened containers

🔧 Engine codes this applies to

DV6C(9HD)DV6C(9HR)

📐 32 workshop diagrams for DV6C(9HD)

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

DS5 - DV6C — DV6C(9HD) · diagram 1
DS5 - DV6C — DV6C(9HD) · diagram 2
DS5 - DV6C — DV6C(9HD) · diagram 3
DS5 - DV6C — DV6C(9HD) · diagram 4
DS5 - DV6C — DV6C(9HD) · diagram 5
DS5 - DV6C — DV6C(9HD) · diagram 6
DS5 - DV6C — DV6C(9HD) · diagram 7
DS5 - DV6C — DV6C(9HD) · diagram 8
+ 24 more diagrams
🔒 32 workshop diagrams for this job Ask about your Citroen DV6C(9HD) — free or sign up free to see the drawings

📋 Procedure

Preparation and removal

  1. Caution! The temperature of the engine and exhaust will increase significantly
  2. Note: The fuel tank should contain at least 20 litres of fuel
  3. Without diagnostic tool:
  4. Select the highest suspension position
  5. Start the engine
DV6C(9HD)? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Run the engine until warm
  2. Connect the diagnostic tool
  3. Remove the underbody cover
  4. Delete all the fault codes
  5. Activate the diesel particulate filter regeneration function
  6. Follow the instructions on the screen of the diagnostic tool
  7. Note: Plug all open lines to prevent damage
  8. Remove the nut shown
  9. Disconnect the battery
  10. Disconnect the filler pipe
  11. Wait until the engine has cooled down
  12. Empty the additive tank

Installation and checks

  1. Note: Do not re-use the drained fluid or fluid from opened containers
  2. Connect the filler pipe from the container to the additive tank
  3. Connect the overflow container pipe to the additive tank
  4. Position the overflow container underneath the vehicle
  5. Lower the vehicle
  6. Raise the filling container above the additive tank
  7. Run the engine at idle speed
  8. Stop the engine
  9. Lower the filling container
  10. Open the valve until the remaining fluid returns to the filling container
  11. Remove the overflow pipe
  12. Disconnect the additive tank filling kit filler pipe from the additive tank filler pipe
  13. Reconnect the filler pipe
  14. Use the diagnostic tool
  15. Reset the additive system
  16. Refit all parts in the reverse order of removal
  17. Refill the additive tank
  18. Use a diagnostic tool
  19. Reprogram the additive pump
  20. Using the diagnostic tool:
  21. Check the additive level
Workshop diagrams

Ask TorqFix about your Citroen DV6C(9HD) — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Citroen DV6C(9HD) — free → or sign up free to see the drawings

Other CITROEN procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.