Servicing wheel bearing housing with V.A.G 1459 B — AUDI

Instead of workshop press V.A.G 1290 A, use can also be made of hydraulic removal and installation tool for wheel bearing and wheel hub V.A.G 1459 B with accessory V.A.G 1459 B /2.

Advantages:

Wheel bearing housing need not be completely dismantled
Track rod end is not detached from wheel bearing housing and wheel alignment is thus not necessary

Special tools and workshop equipment required

V.A.G 1383 A Engine/gearbox lifter with universal gearbox support V.A.G 1359/2
V.A.G 1389 A/1 Foot-operated pump with high-pressure hose

If hand pump V.A.G 1389/1 is already available in workshop, this can be converted to a foot-operated pump.

Make use of conversion kit V.A.G 1389/3 for this purpose.

V.A.G 1459 B Hydraulic removal and installation tool for wheel bearing
Hollow plunger cylinder HKZ-15 with thrust pad E-0-204-T, hydraulic
Pins E-0-217+218
Special nut E-8-214
Thrust pad E-5
Thrust pad E-14-1

V.A.G 1459 B/2 Accessory set
Parting tool Kukko 17/2
Bell E-40
Thrust pad E-43
Thrust sleeve E-44-1
Thrust pad E-45

Parting tool Kukko 17/3

Removing

Slacken off hexagon bolt for drive shaft with vehicle standing on its wheels to avoid danger of accident.
Remove wheel and raise vehicle.

Unscrew drive shaft from drive flange.

1 -
Hexagon socket-head bolt or multi-point socket-head bolt

Pull wire of ABS speed sensor out of holder at brake caliper -arrow-.
Pull ABS speed sensor out of wheel bearing housing.
Detach brake carrier with brake caliper and attach with wire to body.
Remove brake disc and splash plate.

Unscrew nut -1-, take out hexagon bolt and lift out both links -2-.

Slots in wheel bearing housing are never to be widened using a chisel or the like.

If hexagon bolt cannot be removed from wheel bearing housing, bolt and links -2- must be pressed out of wheel bearing housing => Page
40-133.

Screw out hexagon bolt for drive shaft.
Swivel out wheel bearing housing.
Take drive shaft out of wheel bearing housing and tie up.

Note:

Place gearbox lifter V.A.G 1383/A in position (danger of accident caused by falling components on removing wheel hub and wheel bearing).

Removing wheel hub

Insert parting tool -1- between wheel bearing housing and wheel hub and pre-tension.

Installation position: Flat surfaces of edges point towards wheel hub

Fit bell -2-, hollow plunger cylinder -3- with pin and special nut -4-.
Remove wheel hub whilst holding tool.

1 - Parting tool Kukko 17/2
2 - Bell E-40
3 - Hollow plunger cylinder HKZ-15
4 - Special nut E-8-214 and pin
5 - High-pressure hose with quick-release coupling

Removing wheel bearing

Fit thrust pad -1- with collar facing bearing, thrust sleeve -2- with the four stepped inner diameters facing wheel bearing housing, hollow plunger cylinder -3- with pin and special nut -4-.
Remove wheel bearing by way of pump action.

1 - Thrust pad E-5
2 - Thrust sleeve E-44-1
3 - Hollow plunger cylinder HKZ-15
4 - Special nut E-8-214 and pin

Detaching bearing inner race from hub

Fit parting tool -1- behind bearing inner race -2-.

Installation position: Bevel of edges facing bearing inner race

Fit bell -3- and hollow plunger cylinder -4- with pin, screw on with special nut -5- and detach bearing inner race.

1 - Parting tool Kukko 17/2
2 - Bearing inner race
3 - Bell E-40
4 - Hollow plunger cylinder HKZ-15
5 - Special nut E-8-214 and pin

Pressing in wheel bearing

Installation position: Large ID of wheel bearing facing outwards

Place wheel bearing -1-, thrust pad -2- (position collar in bearing) and hollow plunger cylinder -3- with pin in position at wheel bearing housing.
Fit thrust pad -4- with bevels facing wheel bearing housing and special nut -5- from inside.
Press in wheel bearing by way of pump action.

1 - Wheel bearing (different versions: ø 75 mm and ø 82 mm)
2 - Thrust pad E-45 for wheel bearing (ø 75 mm) or thrust pad E-14-1 for wheel bearing (ø 82 mm)
3 - Hollow plunger cylinder HKZ-15
4 - Thrust pad E-43
5 - Special nut E-8-214 and pin

Pressing in wheel hub

Place wheel hub -1- and hollow plunger cylinder -2- with pin in position at wheel bearing.
Fit thrust pad -3- with collar facing special nut -4- from inside.
Press in wheel hub by way of pump action.

1 - Wheel hub
2 - Hollow plunger cylinder HKZ-15
3 - Thrust pad E-5
4 - Special nut E-8-214 and pin

Perform remaining installation operations in reverse order of removal.