Removing and installing restrictor — AUDI
Removing and installing restrictor on Audi: 15 steps. What to remove, in what order, and what to check after.
Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform code 42
- Opens: refrigerant (A/C)
- Also covered elsewhere: Electronic parts catalogue
Don't miss
- Seal open lines and connections at the refrigerant line with suitable caps (to prevent the ingress of dirt and moisture).
- Only fit restrictors of the same type. Restrictors of different colour have different bore diameters Electronic parts catalogue.
📋 Procedure
- Drain the refrigerant circuit Air conditioner with refrigerant R134a87Refrigerant circuit (air conditioner with refrigerant R134a, refrigerant circuit, working with air conditioner service station).
- Remove the luggage compartment pan 70.
- Detach the refrigerant line at the screw connection (A). [Note: Seal open lines and connections at the refrigerant line with suitable caps (to prevent the ingress of dirt and moisture).]
- Use pointed-nose pliers to pull the restrictor (C) out of the refrigerant line. [Note: Only fit restrictors of the same type. Restrictors of different colour have different bore diameters Electronic parts catalogue.]
- Check correct positioning of the O-ring (D) (7.5 mm; 1.5 mm) in the groove.
- Before fitting, moisten the O-ring (of the restrictor and at the screw connection) with a small quantity of refrigeration oil.
- Install the restrictor (C) in the correct position.
- Check proper positioning of the restrictor.
- Replace the O-ring (B); for version, refer to Electronic parts catalogue.
- Take care not to strain the refrigerant lines on installation.
- Tighten the screw connection (A).
- Install the luggage compartment pan 70.
- Evacuate and charge the refrigerant circuit Air conditioner with refrigerant R134a87Refrigerant circuit (air conditioner with refrigerant R134a, refrigerant circuit, working with air conditioner service station).
- Interrogate the event recorder and erase any faults displayed.
- Start up the air conditioner after charging the refrigerant circuit . [Note: Also heed the information on start-up of the air conditioner after charging Air conditioner with refrigerant R134a87General information on air conditioner (air conditioner with refrigerant R134a, general information on air conditioner). Before starting up air conditioner after fresh charging.]
Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Removing and installing subframe - four-wheel drive – Audi
- Servicing drive shaft with 100 mm ∅ outer constant velocity joint
- Removing and installing air supply unit (vehicles with 6-cylinder and 8-cylinder diesel engines, 10-cylinder and 12-cylinder petrol engines)
- Removing and installing gearbox - all vehicles except those with 2.7 ltr. and 4.2 ltr. engine
- Removing and installing gearbox - vehicles with 2.7 ltr. engine
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.