Reading measured value block for gearbox with hydraulic control E17 — AUDI
Reading measured value block for gearbox with hydraulic control E17 on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
Notes:
"Reading measured value block" Section for gearbox with hydraulic control E18/2 => Page
01-236
onwards.
Attention:
To avoid risk of accident when performing measurement and test drives, pay attention to safety precautions => Page
01-32
.
Sequence of operations
Connect up vehicle diagnostic, testing and information system VAS 5051 => Page
01-34
and select vehicle system "02 - Gearbox electronics". Ignition must be on.
Display on VAS 5051:
From list -1- select diagnosis function "08 - Reading measured value block".
Display on VAS 5051:
1 -
Enter display group
Highest possible entry = 255
Use keypad -2- to enter required "display group number" =>List of display groups, Page
01-198
and confirm by touching Q key.
Display on VAS 5051:
1 -
Display zone 1
Display zone 2
Display zone 3
Display zone 4
Notes:
Line remains blank if a display zone is not used.
2 -
Display group required appears here.
3 -
Different display group can be selected by touching these keys.
4 -
Different function can be selected by touching keys -4- (e.g. to switch from "Reading measured value block" to "Basic setting" and back again).
Display on VAS 5051:
A new display group number can be entered by touching ◂ key.
Terminate function "08 - Reading measured value block" by touching ◂ key again.
Display on VAS 5051:
Select diagnosis function "06 - End of output" in list => Page
01-185
.
List of display group numbers available for gearbox with hydraulic control E17
Display group number · Display zone · / Designation · Explanatory notes on Page
001 · 1 / 2 / 3 / 4 · Engine speed / Gearbox input speed sender -G182 / Gearbox speed sender -G38 / Gear engaged
002 · 1 / 2 / 3 / 4 · Driving dynamics index / Throttle valve value / Gearbox speed sender -G38 / Gear engaged · Test table =>Page onwards 01-202
003 · 1 / 2 / 3 / 4 · Brake / "P" "N" lock / Vehicle speed / Supply voltage/pin 54, 55
Continued on next page
List of display group numbers available for gearbox with hydraulic control E17
Display group number · Display zone · / Designation · Explanatory notes on Page
004 · 1 / 2 / 3 / 4 · ATF temperature / Selector lever position / Multi-function switch position / On-board diagnosis information 1) / Engine intervention request 2)
005 · 1 / 2 / 3 / 4 · Solenoid valve 1 -N88 / Solenoid valve 2 -N89 / Solenoid valve 3 -N90 / Gear engaged · Test table =>Page onwards 01-202
006 · 1 / 2 / 3 / 4 · Specified current of solenoid valve 4 -N91 / Specified current of solenoid valve 5 -N92 / Specified current of solenoid valve 6 -N93 / Gear engaged
1)
Vehicles with CAN bus only. For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
2)
Vehicles with no CAN bus only For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
Continued on next page
List of display group numbers available for gearbox with hydraulic control E17
Display group number · Display zone · / Designation · Explanatory notes on Page
007 · 1 / 2 / 3 / 4 · ATF temperature / Specified current of solenoid valve 7 -N94 / Torque converter clutch / Torque converter slip speed · Test table =>Page onwards 01-202
008 · 1 / 2 / 3 / / 4 · Kickdown switch / Throttle valve value / Engine torque in Nm 1) / Throttle valve duty cycle in % 2) / Overrun/"under acceleration"
1)
Vehicles with CAN bus only. For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
2)
Vehicles with no CAN bus only For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
Continued on next page
List of display group numbers available for gearbox with hydraulic control E17
Display group number · Display zone · / Designation · Explanatory notes on Page
009 1) · 1 / 2 / 3 / 4 · Actual engine torque / Maximum torque / Engine speed / Throttle valve value
009 2) · 1 / 2 / 3 / 4 · Actual engine torque / Engine speed / Throttle valve value / Consumption signal · / Test table =>Page onwards 01-202
010 · 1 / 2 / 3 / 4 · Torque increase in torque converter / Engine speed / Gear engaged / Traction control system (TCS)
011 · 1 / 2 / 3 / 4 · Selector lever position / Tiptronic recognition / Change-up/change-down position for Tiptronic switch -F189 / Air conditioner kickdown
1)
Vehicles with CAN bus only. For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
2)
Vehicles with no CAN bus only For a precise definition of which vehicles are fitted with CAN bus, refer to
=> Automatic Gearbox 01V Front and Four-Wheel Drive; Repair Group 00; Code letters, assignment of mechanical units, transmission ratios, features
Automatic Gearbox 01V Front and Four-Wheel Drive
Code letters, assignment of mechanical units, transmission ratios, features
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Dismantling and assembling drive shaft, triple roller joint AAR3300i (with bolted flange on gearbox)
- Removing and installing front seat backrest and seat pan - RS bucket seat
- Calibrating adaptive cruise control - adjustment procedure using ACC setting deviceVAS 6190
- Calibrating adaptive cruise control - adjustment procedure using ACC setting deviceVAS 6430
- Removing gearbox, vehicles with 1.8 ltr. and 2.0 ltr. TFSI engine
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.