Exploded view - front brake, steel version brakes (1LM / 1LX) — AUDI
Exploded view - front brake, steel version brakes (1LM / 1LX) on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
Exploded view - front brake, steel version brakes (1LM / 1LX)
Splash plate for brakes
Chapter
“
Removing and installing splash plate
”
Hub carrier
Bracket
For brake hose and electrical wiring
Bolt
9 Nm
Bolt
With washer
2x
Always renew if removed
196 Nm
Brake hose
Make sure the brake hose is routed correctly. The brake hose must not be kinked, crushed or twisted or chafe against parts of the vehicle at any point.
Renew if damaged
Ensure that lugs are properly seated in grooves in bracket
Tightening torque, brake hose to brake caliper: 20 Nm
Bracket
For brake hose
Retaining spring
Renew if damaged
Brake line
Tightening torque, brake line to brake hose: 14 Nm
Rivet
2x
Bolt
4x
9 Nm
Damper weight
2x
Bolt
For centre retaining pin
Always renew if removed
30 Nm
Protective cap
Pad retaining pin
2x
Renew when changing pads
Note correct installation position
Knock out inwards
Brake pad wear sender
Front left brake pad wear sender
G34
/
front right brake pad wear sender
G35
For inner brake pad
Renew if damaged
Cannot be removed without damage
Removing and installing
Chapter
Pad retaining spring
Note correct installation position
Fig.
Renew when changing pads
Ensure correct positioning in brake caliper
Brake pads
Check pad thickness; wear limit
Maintenance
Booklet
411
Always renew on both sides of one axle
For correct version refer to
Electronic parts catalogue
Note correct position: inner brake pad with retainer for pad wear sender
Chapter
“
Removing and installing brake pads
”
Bleeder screw
13 Nm
Brake caliper
Must not be unbolted from brake carrier
Fig.
For correct version refer to
Electronic parts catalogue
Chapter
“
Removing and installing brake caliper
”
Chapter
“
Renewing brake caliper
”
Servicing
Chapter
Note
Depending on the model, two vibration dampers are fitted on each front brake caliper.
Chapter
“
Vibration dampers on brake caliper
”
Centre retaining pin
Renew when changing pads
Brake disc
Wear limit
Chapter
For correct version refer to
Electronic parts catalogue
Always renew on both sides of one axle
Chapter
“
Removing and installing brake disc
”
Bolt
10 Nm
Bolt
4x
10 Nm
Do not loosen bolts securing brake caliper to brake carrier
Caution
Risk of malfunction
DO NOT slacken off bolts
arrows
on brake caliper.
Installation position of pad retaining spring
Arrow points in direction of forward wheel rotation.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.