TorqFix

Cleaning evaporator with ultrasonic A/C cleanerVAS 6189: Audi A8 D3

Step-by-step cleaning evaporator with ultrasonic A/C cleanerVAS 6189 for the Audi A8 D3: 16 steps. What to remove, in what order, and what to check after.

Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.

16 steps

🧭 Before you start

Fits: Audi A8 D3 (4E, 2002–2010)

Don't miss

  • The odour can only be eliminated by cleaning with the ultrasonic A/C cleanerVAS 6189 if it actually occurs in the evaporator.
  • On this vehicle, the dust and pollen filter is installed at the fresh air intake upstream of the fresh air blower V2 and does not therefore have to be removed for cleaning.
  • The cleaning process takes roughly 15 to 20 minutes and is completed when no further vapour emerges from the outlet hose.

📋 Procedure

  1. By switching from fresh air to air recirculation mode, check whether the air conditioning unit evaporator is really the source of the odour. [Note: The odour can only be eliminated by cleaning with the ultrasonic A/C cleanerVAS 6189 if it actually occurs in the evaporator.]
  2. Check the plenum chamber and the water drain valves fitted in it and clean these if necessary .
  3. Check for odour from and contamination of the dust and pollen filter . [Note: On this vehicle, the dust and pollen filter is installed at the fresh air intake upstream of the fresh air blower V2 and does not therefore have to be removed for cleaning.]
  4. Start the engine.
  5. In the operating and display unit, Climatronic control unit J255"„air recirculation mode“" setting, switch off the compressor ("„Econ mode on“" or "„A/C mode off“").
AUDI? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →
  1. Open the dash panel vents and, on the operating and display unit, Climatronic control unit J255, set the lowest possible temperature for the driver and front passenger side (e.g. "„Lo“" temperature setting).
  2. Close the vehicle windows and sun roof.
  3. Select the lowest fresh air blower speed on the operating and display unit, Climatronic control unit J255 and set the air outflow direction to the "„dash panel vents“".
  4. Shake the bottle of cleaning fluidVAS 6189/1 and pour the fluid into the ultrasonic A/C cleanerVAS 6189. In doing so, heed the operating instructions for the ultrasonic A/C cleanerVAS 6189.
  5. Position the ultrasonic A/C cleanerVAS 6189 in the passenger's footwell.
  6. Start up the ultrasonic A/C cleanerVAS 6189 (in accordance with the appropriate operating instructions) and position the outlet hose such that the vapour emerging is drawn in by the fresh air blower V2 via the air recirculation opening of the air conditioning unit (beneath the dash panel).
  7. Close the vehicle doors. [Note: The cleaning process takes roughly 15 to 20 minutes and is completed when no further vapour emerges from the outlet hose.]
  8. Switch off the ultrasonic A/C cleanerVAS 6189.
  9. Open the vehicle doors and vent the vehicle for at least 10 minutes.
  10. Remove the ultrasonic A/C cleanerVAS 6189 from the vehicle and clean it in line with the appropriate operating instructions.
  11. Switch off ignition.

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.