F9Q-718 engine — Renault 1.9 dCi (1.9L)
1.9L · 107 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | F9Q-718 |
| Capacity | 1870 cc |
| Idle speed | 810 ± 50 rpm |
| Inlet | 0.20 mm |
| Exhaust | 0.40 mm |
| Oil pressure | 1.2 / 1000 3.5 / 3000 bar/rpm |
Engine (diesel)
| System (make and type) | Bosch EDC 15C3 |
| Pressure | 2.5 - 4.0 bar |
| High-pressure pump: | Bosch CR/CP153/R65/10-15 |
| Pressure | 250 - 1350 bar |
| Number of cylinders | 4 |
| Injector firing order | 1-3-4-2 |
| Injector (make and type) | Bosch CR/IPS19/ZEREK10S |
| Glow plug resistance | 0.6 ohms |
| Exhaust gas analysis | 1.8 m-1 |
| Max. no-load governed speed | 4550 - 4850 rpm |
| Turbocharger (make and type) | Garrett |
| Turbo pressure | 0.12 / 1-4 0.40 / 10-12 bar/mm |
Cooling system
| Cap pressure | 1.2 bar |
Electrical
| Alternator | 125 A |
Capacities
| Engine sump, incl. filter | 5.1 l |
| Manual transmission | PK1 |
| Gearbox refill | 2.1 - 2.6 l |
| Cooling system | 8.2 l |
| Air-conditioner refrigerant | 700 ± 35 g |
| Air-conditioner compressor oil | 135 ± 15 ml |
Torque settings
| Cylinder head (bolts) — Stage 1 | 30 Nm |
| Cylinder head (bolts) — Stage 2 | 100 ± 4 ° |
| Cylinder head (bolts) — Stage 5 | 25 Nm |
| Cylinder head (bolts) — Stage 6 | 213 ± 7 ° |
| Repeat stages 4, 5 and 6 for bolts: | 3-4, 5-6, 7-8, 9-10 |
| Cylinder head (bolts) — Stage 2 | 230 ± 6 ° |
| Glow plugs | 15 Nm |
| Main bearing cap | 65 Nm |
| Big-end bearing cap | 50 Nm |
| Flywheel | 50 - 55 Nm |
| Wheel bolts | 100 Nm |
| Front hub | 280 Nm |
| Rear hub | 190 Nm |
Emissions
| Emission code | 70/220*1998/69 |
| Emission standard | Euro 2 (08/1999 ->) |
| CO2 average | 154 g/km |
| CO | 0.119 g/km |
| NOx | 0.406 g/km |
| HC NOx | 0.417 g/km |
| Particles | 0.038 g/km |
| Emission code | 70/220*1996/69 |
| Emission standard | Euro 2 (01/2000 ->) |
| CO | 0.125 g/km |
| HC NOx | 0.407 g/km |
| Emission code | 70/220*1998/69A |
| Emission standard | Euro 3 (09/2000 ->) |
| Emission standard | Euro 2 (09/1999 ->) |
| CO2 average | 149 g/km |
| Emission code | 70/220*1999/102A |
| Emission standard | Euro 3 (01/2001 ->) |
| CO2 average | 152 g/km |
| CO | 0.171 g/km |
| NOx | 0.368 g/km |
| HC NOx | 0.390 g/km |
| Emission code | 70/220*2001/1A |
| Emission standard | Euro 3 (09/2001 ->) |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a F9Q-718 problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.