AUDI CUVB — 2L Engine
2L · 134 hp
Engine overview
Torque figures by job
From the step-by-step procedures for this engine — each figure sits in the step that uses it.
- 20 Nm (15 lb-ft) — ⚠ Make sure not to damage the seal (arrow) in the propshaft flange
- 35 Nm (26 lb-ft) — Tighten nut (B) on assembly tool T10134 to
- 40 Nm (30 lb-ft) — Tighten nut (B) on assembly tool T10134 to
- 45 Nm (33 lb-ft) — Tighten nut on assembly tool T10134 to
- 10 Nm (7.4 lb-ft) — Tighten bolt (1) for camshaft sprocket and nut (2) for high-pressure pump sprocket to
- 20 Nm (15 lb-ft) — Tighten camshaft sprocket bolt to
- 10 Nm (7.4 lb-ft) — Tighten bolt (1) for camshaft sprocket and nut (2) for high-pressure pump sprocket to
- 20 Nm (15 lb-ft) — Tighten camshaft sprocket bolts to
- 20 Nm (15 lb-ft) — Tighten camshaft sprocket bolt to
- 10 Nm (7.4 lb-ft) — Tighten bolts (1) to
- 25 Nm (18 lb-ft) — ⚠ When working on all parts of the exhaust system:Observe safety precautions when working…
- 35 Nm (26 lb-ft) — Tighten bolted connections to
- 9 Nm (6.6 lb-ft) — Tighten bolts (1) to
- 9 Nm (6.6 lb-ft) — ⚠ When installing a new base engine, it is essential that the clamping pieces for the…
- 9 Nm (6.6 lb-ft) — Tighten bolt (2) to
Engine codes in the same family
The same code prefix usually means the same block with a different output, fuel or model year. Procedures are often shared — check the code on the engine plate.
Workshop procedures for this engine
Step-by-step procedures from the workshop database, carrying 22 torque figures.
- Detaching toothed belt from camshaft · 8 torque figures
- Removing and installing emission control module · 3 torque figures
- Separating engine and gearbox - vehicles with manual gearbox · 4 torque figures
- Separating engine and gearbox - vehicles with dual clutch gearbox · 2 torque figures
- Removing and installing fuel delivery unit/fuel gauge sender
- Removing and installing toothed belt cover (top)
- Removing and installing water radiator for charge air cooling circuit
- Installing high-pressure pipe · 1 torque figures
- Removing and installing coolant pipes (top)
- Removing and installing coolant pipe (front left)
- Removing and installing coolant pipe (bottom front)
- Removing and installing exhaust gas recirculation control motor 2V339
- Removing and installing auxiliary pump for heating V488
- Removing and installing control valve for camshaft control valve 1N205
- Removing and installing toothed belt cover (bottom)
- Removing and installing charge air cooling pump V188
- Exploded view - sump (2-part)
- Removing and installing exhaust gas temperature sender 3 G495/exhaust gas temperature sender 4 G648
- Exploded view - cylinder block (pulley end) · 4 torque figures
Got a CUVB problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 2 Oct 2026.