113.963 engine — Mercedes-Benz 5.0 (5L)
5L · 306 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | 113.963 |
| Capacity | 4966 cc |
| Idle speed | 650 - 800 rpm |
| Normal | 12.0 - 14.0 bar |
| Minimum | 9.0 bar |
| Normal | 10.0 - 12.0 bar |
| Minimum | 8.0 bar |
| Differential limit between cylinders | < 1.5 bar |
| Oil pressure | > 0.7 / 700 > 3.0 / 3000 bar/rpm |
Engine (petrol)
| Fuel system (make and type) | Bosch Motronic ME 2.8 |
| Number of cylinders | 8 |
| Firing order | 1-5-4-2-6-3-7-8 |
| Injection pressure/system pressure | 3.7 - 4.1 bar |
| Spark plugs (make and type) | Mercedes A0041591903, A0041595003, A0031599403 |
| Spark plug gap | 0.8 mm |
| Lambda | 0.97 – 1.03 |
| CO exhaust gas | < 0.5 % |
| CO at fast-idle speed | < 0.3 % |
Cooling system
| Cap pressure | 1.4 ± 0.1 bar |
| Thermostat opens at | 87 ± 2 °C |
| Thermostat fully open at | 102 °C |
Electrical
| Battery | 70 / 74 Ah |
| Alternator | 150 A |
Capacities
| Engine sump, incl. filter | 7.5 l |
| Automatic transmission | 722.633 |
| Initial filling | 8.6 (+ 0.5) l |
| Automatic transmission | 722.901 |
| Initial filling | 9.0 l |
| Differential | 1.1 l |
| Differential | 1.6 l |
| Differential | 1.2 l |
| Differential | 1.9 l |
| Cooling system | 11.5 l |
| Air-conditioner refrigerant | 920 g |
| Air-conditioner compressor oil | 120 ml |
Torque settings
| Cylinder head bolts — Stage 1 | 10 Nm |
| Cylinder head bolts — Stage 2 | 30 Nm |
| Cylinder head bolts — Stage 3 | 90 ° |
| Cylinder head bolts — Stage 4 | 90 ° |
| Cylinder head bolts — Stage 1 | 20 Nm |
| Spark plugs | 28 Nm |
| Oxygen sensor | 55 Nm |
| Main bearing cap — Stage 1 | 20 Nm |
| Main bearing cap — Stage 2 | 90 ° |
| Main bearing cap — Stage 1 | 5 Nm |
| Main bearing cap — Stage 2 | 30 Nm |
| Main bearing cap — Stage 3 | 90 ° |
| Side bolt of main bearing cap | 30 Nm |
| Big-end bearing cap — Stage 1 | 5 Nm |
| Big-end bearing cap — Stage 2 | 90 Nm |
| Big-end bearing cap — Stage 3 | 90 ° |
| Automatic transmission drain plug | 20 Nm |
| Wheel nuts | 130 Nm |
| Rear hub | 320 Nm |
Emissions
| Emission code | 70/220*2001/1A |
| Emission standard | Euro 3 (06/2001 ->) |
| CO2 average | 304 g/km |
| CO | 0.535 g/km |
| HC | 0.064 g/km |
| NOx | 0.009 g/km |
| Emission code | 70/220*2001/1B |
| Emission standard | Euro 4 (06/2001 ->) |
| Emission code | 70/220*2001/100B |
| Emission standard | Euro 4 (12/2002 ->) |
| CO2 average | 292 - 304 g/km |
| CO | 0.378 - 0.535 g/km |
| HC | 0.062 - 0.064 g/km |
| NOx | 0.009 - 0.015 g/km |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a 113.963 problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.