Corsa B 16V DOHC petrol X14XE, C14SEL, X16XE, C16SEL, except C16XE — OPEL / VAUXHALL
Corsa B 16V DOHC petrol X14XE, C14SEL, X16XE, C16SEL, except C16XE on Opel / Vauxhall: 103 steps, engines C14SEL, C16SEL, C16XE, X14XE.
Workshop procedure for OPEL / VAUXHALL — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform codes 1.4I, 16V, |, 1.6I
- Timing position: the crankshaft or camshaft is set and locked during this job
Don't miss
- Use a wrench to counterhold
📋 Procedure
Preparation and removal
- Before disconnecting the battery cable, check the audio system security code
- Coolant pump renewal is recommended after timing belt removal
- Check the timing marks
- Lock the camshafts
- Check the tensioner and idler pulleys; renew if necessary
- Release the ancillary drive belt tension
- Disconnect the reaction link
- Remove the engine support
- Steel oil sump:
- Remove the flywheel inspection cover plate
- Remove the crankshaft pulley
- Note: Use a wrench to counterhold
- Use new bolt(s)
- Remove the plug
- Stage 2:
- Note: Use a wrench to counterhold
- Remove the timing belt lower cover
- Lock the camshafts
- Remove the tensioner
Installation and checks
- Note: The belt area between camshaft and crankshaft should be stretched
- Vehicles with power steering:
- Turn the tensioner clockwise
- Note: Avoid bending, torsion or traction
- Vehicles with power steering and air conditioning:
- Turn the crankshaft clockwise 2 rotations
- Tension the timing belt
- Lock the tensioner
- Turn the tensioner clockwise
- Turn the tensioner as shown
- Check the timing marks again
- Check the timing marks and tension again
- Vehicles without power steering and air conditioning:
- Refit the ancillary drive belt
- Align the timing marks
- Fit the ancillary drive belt
- Refit the engine support
- Note: Lift the engine
- Stage 1:
- Stage 2:
- Stage 3:
- Renew the bolt(s)
- Refit the cover
- Refit the engine support
- Remove the engine support bar
- All vehicles:
- Refit the air filter with the inlet hose
Other OPEL / VAUXHALL procedures
- Corsa B Clutch 1.2/1.4 Except X12XE (With service aperture); Astra F 1.4
- Opel Corsa C 1.2 CDTI timing chain replacement
- Opel Astra G 2.2 DTI Y22DTR timing chain replacement
- Opel VectraC, Signum 2.8 Z28NEL timing chain replacement
- Opel Astra G 2003 2.0 DTI Y20DTH timing chain replacement
- Opel Astra G X Y 20DTL 2.0 DTI X20DTL timing chain replacement
- Vectra C F40 Z20NET Gearbox
- Vectra C M32 Z22YH Gearbox
- Vectra C F40 Z28NEL Z28NET Gearbox
- Zafira B M32 Z22YH Gearbox
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.