Removing and installing TV aerial amplifier -Saloon- — AUDI
Removing and installing TV aerial amplifier -Saloon- on Audi: factory workshop procedure. Full factory text, tools and checks.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
ℹ️ Torque figures below come verbatim from workshop data — always cross-check against your vehicle's factory manual before final tightening.
(up to vehicle identification no. 8DZYA200000)
The four TV aerial amplifiers are installed under the rear shelf.
Removing
First remove the rear shelf
=> General Body Assembly, Interior; Repair group 70; Trims; Removing and installing rear shelf
General Body Assembly, Interior
Trims
Removing and installing rear shelf
Each of the four TV aerial amplifiers -1- are attached to a bracket -2- with a bolt and nut -3- (2.5 Nm) and an anti-twist element. The bracket is then attached to the rear shelf via two screws -4- (2.5 Nm).
Remove bolt and nut -3- (2.5 Nm).
Disconnect the electrical connectors and remove the TV aerial amplifier -1-.
Installing:
Installation is performed in the reverse sequence to removal.
(from vehicle identification no. 8DZYA200001)
Three of the four TV aerial amplifiers are installed under the rear shelf. One TV aerial amplifier is bolted on right at D-pillar.
Removing and installing TV aerial amplifier under rear shelf
Removing
First remove the rear shelf
=> General Body Assembly, Interior; Repair group 70; Trims; Removing and installing rear shelf
General Body Assembly, Interior
Trims
Removing and installing rear shelf
Each of the three TV aerial amplifiers -1- are attached to a bracket -2- with a bolt and nut -3- (2.5 Nm) and an anti-twist element. The bracket is then attached to the rear shelf via two screws -4- (4.5 Nm).
Remove bolt and nut -3- (2.5 Nm).
Disconnect the electrical connectors and remove the TV aerial amplifier -1-.
Installing:
Installation is performed in the reverse sequence to removal.
Removing and installing TV aerial amplifier at D-pillar
Removing
One aerial amplifier -3- is bolted to D-pillar -1- under rear shelf -2-.
Remove C/D-pillar trim.
=> General Body Assembly, Interior; Repair group 70; Trims; Removing and installing C/D-pillar trim
General Body Assembly, Interior
Trims
Removing and installing C/D-pillar trim
The aerial amplifier is attached to the D-pillar with a cross-head screw -2- (2.5 Nm) and an anti-twist element -1-.
Disconnect the electrical connectors and remove the TV aerial amplifier.
Installing:
Installation is carried out in reverse sequence to removal.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Repairing a wire of 0.22 mm2 section by connecting in an additional wire
- Removing and installing automatic gearbox control unit J217
- Servicing 6-speed manual gearbox 0A2, front-wheel drive — Servicing gearbox housing
- Removing and installing rear splined shaft, oil seal and ball bearing
- Removing and installing oil pump and suction-jet pump
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.