Removing and installing overhead view camera control unit J928, up to model year 2013, including vehicles with high-voltage electrical system — AUDI
Removing and installing overhead view camera control unit J928, up to model year 2013, including vehicles with high-voltage electrical system on Audi.
Workshop procedure for AUDI — the factory write-up, straight from real workshop data.
📋 Procedure
Removing and installing
overhead view camera control unit
J928
, up to model year 2013, including vehicles with high-voltage electrical system
The
control unit for overhead view camera
J928
1
is located in the luggage compartment on the back panel (left-side).
Note
If control unit is to be renewed, select the
“Replace control unit”
function for appropriate control unit in
Vehicle diagnostic tester
.
Switch off ignition and all electrical equipment and remove ignition key.
Removing
Remove luggage compartment back panel trim
General body repairs, interior
Rep. gr.
70
Luggage compartment trim panels; Exploded view - luggage compartment side trim
.
The
control unit for overhead view camera
J928
1
is only wedged in the bracket.
High-voltage vehicles only
Installing the high-voltage battery (
hybrid battery unit
AX1
) in the luggage compartment restricts the installation space around the
overhead view camera control unit
J928
. The
hybrid battery unit
AX1
in the luggage compartment must be moved back and placed on the
rails
T40275
first.
Observe warning instructions for work on the high-voltage system
Electrical system
Rep. gr.
93
General warning instructions for work on the high-voltage system
.
Perform steps for removal of
hybrid battery unit
AX1
to the point where it can be set down in the luggage compartment
Electrical system
Rep. gr.
93
High-voltage battery unit; Exploded view - high-voltage battery
.
All vehicles
Release and unplug connectors at
control unit for overhead view camera
J928
1
.
Use a small screwdriver to press retainers
arrow
towards right side and pull
control unit for overhead view camera
J928
out of bracket.
Installing
Installation is carried out in reverse sequence; note the following:
High-voltage vehicles only
Observe warning instructions for work on the high-voltage system
Electrical system
Rep. gr.
93
General warning instructions for work on the high-voltage system
.
Install
hybrid battery unit
AX1
Electrical system
Rep. gr.
93
High-voltage battery unit; Exploded view - high-voltage battery
.
All vehicles
Perform calibration
Chapter
“
Calibrating overhead view camera system
”
.
TorqFix answers live for your specific car — tell it the engine code and it serves the matching sequence, torque figures and wiring for that exact variant.
Ask about my car →Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Removing toothed belt from camshaft sprockets – Audi · 2 torque figures
- Removing sump (top section) – Audi A4 B5 · 2 torque figures
- Removing and installing power-assisted steering box · 2 torque figures
- Removing and installing toothed belt, engine code BLX, BLY, BLR, BVY, BVZ · 2 torque figures
- Audi CEPA/CEPB gearbox removal & installation · 2 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.