Removing and installing ISOFIX child seat anchor (rear): Audi TT Mk2
Step-by-step removing and installing ISOFIX child seat anchor (rear) for the Audi TT Mk2: 11 steps. What to remove, in what order, and what to check after.
Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: Audi TT Mk2 (8J, 2006–2014)
Don't miss
- For greater clarity the padding is shown without the cover.
- Make sure electrical connectors are fitted correctly (as far as stop) and engage audibly.
- If airbag warning lamp K75 indicates a fault following installation, you must interrogate, erase and then re-interrogate the fault memory .
📋 Procedure
- ⚠ Observe safety regulations for pyrotechnic components .Before handling the airbag units (e.g. unplugging the electrical connector) the mechanic must discharge static electricity by briefly touching the door striker plate, or similar. — Remove front passenger's seat:
- Attach front seat to seat repair standVAS 6136.
- Remove backrest:
- If fitted, disengage tensioning straps (left and right) (arrow).
- Disengage fastening strips (1), (2) and (3) on back of seat pan (4).
- Pull cover to front off ISOFIX brackets.
- Remove bolts (3) (4x). [Note: For greater clarity the padding is shown without the cover.]
- Lift retainer (1) off seat pan (2). [Note: Make sure electrical connectors are fitted correctly (as far as stop) and engage audibly.]
- ⚠ Observe safety regulations for pyrotechnic components .Before handling the airbag units (e.g. plugging in the electrical connector) the mechanic must discharge static electricity by briefly touching the door striker plate, or similar. — Switch on ignition.
- ⚠ The battery must be connected with the ignition switched on. If pyrotechnic components (e.g. airbag or belt tensioner) are inexpertly repaired, this may result in unwanted triggering after connecting the battery. There must not be anyone in the vehicle while you are connecting the battery. — Connect battery earth wire with ignition switched on Electrical system27Battery; Disconnecting and connecting battery.
- If airbag warning lamp K75 indicates a fault following installation, you must interrogate, erase and then re-interrogate the fault memory .
Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Removing and installing relay and fuse holder in luggage compartment (right-side)
- Renewing flange shaft oil seal (left-side) with gearbox installed
- Removing and installing air filter element (left and right)
- 10-cylinder direct petrol injection engine (5.0 ltr. 4-valve turbo RS 6), mechanics — Securing engine to engine and gearbox support · 1 torque figures
- 6-cylinder TDI engine (2.7 ltr.; 3.0 ltr. 4-valve common rail, EU5), mechanics — Securing engine to engine and gearbox support · 1 torque figures
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.