Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — AUDI

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 on Audi: 17 steps, engines CALB.

Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.

17 steps 1 engine code

🧭 Before you start

Fits: Audi Q5 (8R, 2008–2017)

Renewed: gaskets

Don't miss

Disregard (arrows).
Renew gaskets and self-locking nuts.

🔧 Engine codes this applies to

CALB

📐 35 workshop diagrams for CALB

Real factory drawings for this job — timing marks, bolt locations and routing. Locked in the free view.

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 1

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 2

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 3

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 4

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 5

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 6

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 7

Removing and installing exhaust manifold (right-side) - vehicles with automatic gearbox 0B6 — CALB · diagram 8

+ 27 more diagrams

🔒 35 workshop diagrams for this job Ask about your Audi CALB — free or sign up free to see the drawings

📋 Procedure

Remove noise insulation (1) and (2)General body repairs, exterior66Noise insulation; Exploded view - noise insulation.
Remove plenum chamber partition panel General body repairs, exterior50Bulkhead; Exploded view - plenum chamber partition panel.
Remove Lambda probe G39(item 1).
Remove catalytic converter (right-side) .
Remove air cleaner housing .

CALB? Steps differ between engine variants — check this job against your exact car before you commit to it. Check my car — free →

Remove engine mounting (right-side) .
Remove nut (1) and bolt (2) and push coolant pipe clear to one side. [Note: Disregard (arrows).]
Remove bolts (1 … 4) and detach heat shield.
Remove nuts (7) and (9) and detach bracket for heat shield.
Remove nuts (1 … 6) and (8) and detach exhaust manifold. [Note: Renew gaskets and self-locking nuts.]
Fit exhaust manifold with gasket for catalytic converter and tighten nuts .
Install engine mounting (right-side) .
Install air cleaner housing .
Install catalytic converter (right-side) .
Install Lambda probe G39
Install plenum chamber partition panel General body repairs, exterior50Bulkhead; Exploded view - plenum chamber partition panel.
Install noise insulation panels General body repairs, exterior66Noise insulation; Exploded view - noise insulation.

Workshop diagrams

Ask TorqFix about your Audi CALB — it answers with the exact sequence for that engine and the workshop drawing for each step. First question is free after a 20-second sign-up, no card.

Ask about your Audi CALB — free → or sign up free to see the drawings

Other AUDI procedures

Who makes these pages, and how

TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.

The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.

Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.

Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com

The story behind TorqFix →

Workshop data on this page last updated 20 Sep 2026.