Installing warning lamp for airbag deactivated on front passenger side K145 — AUDI

🧭 Before you start

Fits: Audi A4 Cabriolet B6/B7 (8H), Audi A2 (8Z), Audi A3 (8L, 1996–2003), Audi A4 B5 (8D), Audi A4 B6/B7 (8E), Audi A6 C5 (4B), Audi A8 D2 (4D), Audi A8 D3 (4E, 2002–2010), Audi A3 (8P, 2003–2012), Audi TT Mk1 (8N), Audi A6 C6 (4F, 2004–2011)

Don't miss

• Check whether wiring harness for warning lamp for airbag deactivated on front passenger side K145 ("“PASSENGER AIRBAG OFF”" lamp) has been installed in area of radio opening (wire with blue 6-pin connector).
• Plug in connector (1) at warning lamp for airbag deactivated on front passenger side K145(2).
• Make sure connector (1) and warning lamp for airbag deactivated on front passenger side K145(2) engage properly (audibly).
• Insert warning lamp for airbag deactivated on front passenger side K145(2) in dash panel switch mounting and engage.
• Make sure nobody is in the vehicle when the battery is being connected. — Connect battery earth strap Electrical system27.

📋 Procedure

1. Remove radio Communication91.
2. Open glove box.
3. Carefully detach trim (1) in direction of (arrow) with front-end hook3370.
4. Use a commercially available flat screwdriver to carefully prise dummy cover (1) out of switch mounting (2) in direction of (arrow).
5. Check whether wiring harness for warning lamp for airbag deactivated on front passenger side K145 ("“PASSENGER AIRBAG OFF”" lamp) has been installed in area of radio opening (wire with blue 6-pin connector).

6. Guide free connector (1) (blue) at wiring harness through free chamber of switch insert from rear.
7. Plug in connector (1) at warning lamp for airbag deactivated on front passenger side K145(2).
8. Make sure connector (1) and warning lamp for airbag deactivated on front passenger side K145(2) engage properly (audibly).
9. Insert warning lamp for airbag deactivated on front passenger side K145(2) in dash panel switch mounting and engage.
10. Clip in trim for switch module at top.
11. Close glove box.
12. Install radio Communication91.
13. Switch on ignition.
14. ⚠ Make sure nobody is in the vehicle when the battery is being connected. — Connect battery earth strap Electrical system27.
15. Observe measures to be taken after connecting the battery Electrical system27.
16. Re-code airbag control unit J234.
17. Perform functional test.
18. Deactivate airbag on front passenger side with key-operated switch to deactivate airbag on front passenger side E224.
19. Activate airbag on front passenger side with key-operated switch to deactivate airbag on front passenger side E224.
20. Interrogate and erase fault memories of all control units. To do so, use a suitable vehicle diagnostic, testing and information system, e.g. vehicle diagnostic, testing and information systemVAS 5051B.

Other AUDI procedures

• Removing and installing toothed belt – Audi · 56 torque figures
• Removing engine – Audi A8 D3 · 41 torque figures
• Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
• Installing engine – Audi A8 D4 · 36 torque figures
• Removing and installing camshaft timing chain · 29 torque figures
• Renewing bracket of refrigerant lines · 2 torque figures
• Removing and installing alternator, 1.9 l diesel engine, unit injector (TDI)
• Checking delivery pressure and tandem pump for leaks - engine codes BJB, BLS, BSU
• Assembly overview - sealing flange, belt pulley end · 2 torque figures
• Removing and installing oil filter housing with engine oil cooler