Cleaning air conditioner evaporator — AUDI
Cleaning air conditioner evaporator on Audi: 19 steps. What to remove, in what order, and what to check after.
Workshop procedure for AUDI — the exact step sequence and torque figures, straight from real workshop data.
🧭 Before you start
Fits: platform code 42
- Also covered elsewhere: Operating instructions of VAS 6189A
Don't miss
- For handling of ultrasonic A/C cleaner, refer to Operating instructions of VAS 6189A.
- Cleaning takes roughly 15 to 20 minutes. The cleaning process is over when no further vapour emerges from the outlet hose.
📋 Procedure
- Select the path:
- By switching from fresh-air to air recirculation mode, check whether the air conditioning unit evaporator is really the source of the odour Possible cause of odour formation at the air conditioner.
- Remove the dust and pollen filters .
- Clean the mounting slot for the dust and pollen filters .
- Seal the opening at the air conditioning unit through which the dust and pollen filter was removed.
- Start the engine.
- On the operating unit, Climatronic control unit J255, set "“air recirculation mode”" and switch off the air conditioner compressor (lamp in AC (or A/C) button not lit).
- Open the dash panel vents and, on the operating unit, Climatronic control unit J255, set the rotary temperature control to the "“Cold”" stop.
- Close the vehicle windows.
- Select the lowest fresh air blower speed on the operating unit, Climatronic control unit J255 and set the rotary air distribution control to "“dash panel vents”".
- Shake the bottle of cleaning fluidVAS 6189/1 and pour the fluid into the ultrasonic A/C cleanerVAS 6189A. [Note: For handling of ultrasonic A/C cleaner, refer to Operating instructions of VAS 6189A.]
- Position the ultrasonic A/C cleanerVAS 6189A in the passenger's footwell.
- Start up the ultrasonic A/C cleanerVAS 6189A (in accordance with the appropriate operating instructions) and position the outlet hose such that the vapour emerging is drawn in by the fresh air blower V2 via the air recirculation opening of the air conditioning unit (beneath the dash panel).
- Close the vehicle doors. [Note: Cleaning takes roughly 15 to 20 minutes. The cleaning process is over when no further vapour emerges from the outlet hose.]
- Switch off the ultrasonic A/C cleanerVAS 6189A.
- Open the vehicle doors and vent the vehicle for at least 10 minutes.
- Remove the ultrasonic A/C cleanerVAS 6189A from the vehicle and clean it.
- Switch off the ignition.
- Fit the dust and pollen filters .
Other AUDI procedures
- Removing and installing toothed belt – Audi · 56 torque figures
- Removing engine – Audi A8 D3 · 41 torque figures
- Removing camshaft timing chain from camshafts – Audi A6/A7 C7 · 38 torque figures
- Installing engine – Audi A8 D4 · 36 torque figures
- Removing and installing camshaft timing chain · 29 torque figures
- Dismantling and assembling piston/cylinder "„D"" – Audi
- Removing and installing vacuum pump, 2.0 ltr. TDI engine
- Removing and installing sunroof panel (rear) – Audi Q5 · 1 torque figures
- Renewing seals for glass panel (rear) – Audi Q5
- Removing and installing ATF lines - vehicles with 4-cyl. engine
Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 20 Sep 2026.