P1772 — 4 documented meanings by make

P1772 does not mean the same thing on every car — manufacturers reuse the number for different faults. 7 makes document it: Audi, Chrysler, Ford, Mazda, SEAT, Skoda, Volkswagen. Find your make below.

P1772 on Audi, SEAT, Skoda, Volkswagen

On Audi, SEAT, Skoda, Volkswagen vehicles P1772 is documented as: Load signal stuck on. P1772 is stored when the ECU sees stuck or jammed on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Carbon or oil deposits binding the mechanism; Actuator motor or solenoid failed; Linkage worn or seized; Control side working correctly but the part cannot physically move.

Check first, cheapest first:

1. Command the actuator with a scanner and watch whether it moves at all
2. Remove and inspect for deposits — cleaning frequently fixes this class outright
3. Check the electrical side is delivering the command before condemning the mechanism
4. Inspect the linkage for wear or seizure
5. Replace the actuator if it will not move under command with good supply

Related Audi, SEAT, Skoda, Volkswagen codes:

P1772 on Chrysler

On Chrysler vehicles P1772 is documented as: LR inadequate element volume: LR 2-4 OD.

Related Chrysler codes:

P1772 on Ford

On Ford vehicles P1772 is documented as: Throttle position circuit below minimum voltage. P1772 is stored when the ECU sees signal too low on throttle body or pedal position. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Ford codes:

P1772 on Mazda

On Mazda vehicles P1772 is documented as: Throttle position sensor circuit low input. P1772 is stored when the ECU sees signal too low on throttle body or pedal position. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Mazda codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

P1xxx is manufacturer-specific code (VW/Audi, BMW, Mercedes, Toyota etc. have different meanings for the same code number).

Severity

Manufacturer-specific codes need a brand scanner (VCDS for VAG, INPA for BMW, STAR for Mercedes).

That is what holds for P1772 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.