P1694 — 12 documented meanings by make

P1694 does not mean the same thing on every car — manufacturers reuse the number for different faults. 16 makes document it: Audi, Chevrolet (USA), Chrysler, Citroen, Ford, Hyundai, Kia, Land & Range Rover, Lexus, Mazda, Opel / Vauxhall, Peugeot, SEAT, Skoda, Toyota, Volkswagen. Find your make below.

P1694 on Audi, SEAT, Skoda, Volkswagen

On Audi, SEAT, Skoda, Volkswagen vehicles P1694 is documented as: Self-diagnosis fault light, K83, open or short circuit to ground. P1694 is stored when the ECU sees short to ground on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring insulation chafed through where the loom passes a bracket or edge; Water or salt in a connector bridging the signal pin to the body; The component itself shorted internally; A harness pinched during earlier repair work.

Check first, cheapest first:

1. Unplug the component and re-read the code — if it changes, the fault is in the component, not the wiring
2. Inspect the loom where it passes metal edges, brackets and hinges
3. Open the connector and check for green corrosion or moisture
4. Measure resistance from the signal pin to a body ground; near-zero confirms the short
5. Repair the harness section, or replace the component if it shorted internally

Related Audi, SEAT, Skoda, Volkswagen codes:

P1694 on Chevrolet (USA)

On Chevrolet (USA) vehicles P1694 is documented as: Tachometer circuit, high voltage. P1694 is stored when the ECU sees signal too high on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Chevrolet (USA) codes:

P1694 on Chrysler

On Chrysler vehicles P1694 is documented as: No CCD message from PCM - AISIN transmission. P1694 points at transmission. The standard definition names the system involved; which part inside it has actually failed is what the checks below establish, cheapest first.

Related Chrysler codes:

P1694 on Citroen, Ford, Mazda

On Citroen, Ford, Mazda vehicles P1694 is documented as: Turbo charge relief circuit.

Related Citroen, Ford, Mazda codes:

P1694 on Hyundai

On Hyundai vehicles P1694 is documented as: Immobiliser ECU signal, engine control module signal. P1694 points at immobiliser / key. The standard definition names the system involved; which part inside it has actually failed is what the checks below establish, cheapest first.

Related Hyundai codes:

P1694 on Kia

On Kia vehicles P1694 is documented as: Engine management system message.

Related Kia codes:

P1694 on Land & Range Rover

On Land & Range Rover vehicles P1694 is documented as: Immobilisation ECU code exchange fault. Last occurrence - signal fault. P1694 is stored when the ECU sees malfunction on control module. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Land & Range Rover codes:

P1694 on Lexus

On Lexus vehicles P1694 is documented as: Oil control valve closed fault. P1694 is stored when the ECU sees malfunction on oil pressure or level. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Lexus codes:

P1694 on Opel / Vauxhall

On Opel / Vauxhall vehicles P1694 is documented as: Glow time telltale, open circuit; Glow time telltale circuit high input. P1694 is stored when the ECU sees open circuit on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Broken wire, most often at a flex point such as a door hinge or engine mount; Corroded or pushed-back terminal in the connector; Blown fuse on the supply side; Component failed with an internally open winding or element.

Check first, cheapest first:

1. Check the relevant fuse first — it is the cheapest thing that produces this code
2. Unplug and inspect both halves of the connector for corrosion and terminal fit
3. Continuity-test the wire end to end while flexing the loom by hand
4. Measure the component itself against its specification
5. Repair the break or replace the component, whichever the measurement points to

Related Opel / Vauxhall codes:

P1694 on Peugeot

On Peugeot vehicles P1694 is documented as: Oil Pressure Control Solenoid Circuit Malfunction. P1694 is stored when the ECU sees malfunction on oil pressure or level. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Peugeot codes:

P1694 on Toyota

On Toyota vehicles P1694 is documented as: Oil control valve closed. P1694 points at oil pressure or level. The standard definition names the system involved; which part inside it has actually failed is what the checks below establish, cheapest first.

Related Toyota codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

P1xxx is manufacturer-specific code (VW/Audi, BMW, Mercedes, Toyota etc. have different meanings for the same code number).

Severity

Manufacturer-specific codes need a brand scanner (VCDS for VAG, INPA for BMW, STAR for Mercedes).

That is what holds for P1694 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.