P1444 — 8 documented meanings by make

P1444 does not mean the same thing on every car — manufacturers reuse the number for different faults. 11 makes document it: Audi, BMW, Citroen, Ford, Mazda, Nissan, Peugeot, Saab, SEAT, Skoda, Volkswagen. Find your make below.

P1444 on Audi, SEAT, Skoda, Volkswagen

On Audi, SEAT, Skoda, Volkswagen vehicles P1444 is documented as: Exhaust gas recirculation potentiometer, G212, implausible signal. P1444 is stored when the ECU sees range or performance on EGR system. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Sensor reading is inside its electrical range but does not match reality; Contamination or deposits changing what the sensor sees; A mechanical fault upstream that the sensor is correctly reporting; Sensor drifted with age without failing outright.

Check first, cheapest first:

1. Compare the live value against a second sensor or a known-good figure — this code is about plausibility, not a dead circuit
2. Look for the mechanical cause first: leaks, restrictions or wear that would genuinely produce this reading
3. Clean the sensor if it is the type that fouls
4. Check freeze-frame data to see under what conditions it triggered
5. Replace the sensor only after the mechanical side is ruled out

Related Audi, SEAT, Skoda, Volkswagen codes:

P1444 on BMW

On BMW vehicles P1444 is documented as: Diagnostic module tank leakage (DM-TL) pump control, open circuit. P1444 is stored when the ECU sees open circuit on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Broken wire, most often at a flex point such as a door hinge or engine mount; Corroded or pushed-back terminal in the connector; Blown fuse on the supply side; Component failed with an internally open winding or element.

Check first, cheapest first:

1. Check the relevant fuse first — it is the cheapest thing that produces this code
2. Unplug and inspect both halves of the connector for corrosion and terminal fit
3. Continuity-test the wire end to end while flexing the loom by hand
4. Measure the component itself against its specification
5. Repair the break or replace the component, whichever the measurement points to

Related BMW codes:

P1444 on Citroen, Peugeot

On Citroen, Peugeot vehicles P1444 is documented as: Purge flow sensor circuit low input. P1444 is stored when the ECU sees signal too low on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Citroen, Peugeot codes:

P1444 on Ford

On Ford vehicles P1444 is documented as: Evaporative emission system purge flow sensor circuit low input. P1444 is stored when the ECU sees signal too low on evaporative emissions system. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Ford codes:

P1444 on Mazda

On Mazda vehicles P1444 is documented as: Evaporative emission system purge flow sensor circuit, low voltage. P1444 is stored when the ECU sees signal too low on evaporative emissions system. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Mazda codes:

P1444 on Nissan

On Nissan vehicles P1444 is documented as: Purge volume control valve.

Related Nissan codes:

P1444 on Saab

On Saab vehicles P1444 is documented as: Canister close valve, open circuit; Canister close valve, short circuit to ground. P1444 is stored when the ECU sees open circuit on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Broken wire, most often at a flex point such as a door hinge or engine mount; Corroded or pushed-back terminal in the connector; Blown fuse on the supply side; Component failed with an internally open winding or element.

Check first, cheapest first:

1. Check the relevant fuse first — it is the cheapest thing that produces this code
2. Unplug and inspect both halves of the connector for corrosion and terminal fit
3. Continuity-test the wire end to end while flexing the loom by hand
4. Measure the component itself against its specification
5. Repair the break or replace the component, whichever the measurement points to

Related Saab codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

P1xxx is manufacturer-specific code (VW/Audi, BMW, Mercedes, Toyota etc. have different meanings for the same code number).

Severity

Manufacturer-specific codes need a brand scanner (VCDS for VAG, INPA for BMW, STAR for Mercedes).

That is what holds for P1444 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.