P1108 — 14 documented meanings by make

P1108 does not mean the same thing on every car — manufacturers reuse the number for different faults. 16 makes document it: Audi, Chevrolet (USA), Citroen, Ford, Honda, Isuzu, Jaguar, Mazda, Peugeot, Saab, SEAT, Skoda, SsangYong, Subaru, Suzuki, Volkswagen. Find your make below.

P1108 on Audi, SEAT, Skoda, Volkswagen

On Audi, SEAT, Skoda, Volkswagen vehicles P1108 is documented as: Heating circuit, bank 2, oxygen sensor 1, performance too low. P1108 is stored when the ECU sees signal too low on oxygen sensor (bank 2, sensor 1). That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Audi, SEAT, Skoda, Volkswagen codes:

P1108 on Chevrolet (USA)

On Chevrolet (USA) vehicles P1108 is documented as: Barometric pressure to MAP signal circuit comparison too high. P1108 is stored when the ECU sees signal too high on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Chevrolet (USA) codes:

P1108 on Citroen

On Citroen vehicles P1108 is documented as: Adaptation air inlet fault; EDC15C2, fan high speed circuit, open circuit or short circuit to ground; Dual alternator battery light circuit/BARO to MAP sensor comparison too high. P1108 is stored when the ECU sees malfunction on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Citroen codes:

P1108 on Ford

On Ford vehicles P1108 is documented as: MAP sensor circuit, high voltage; Dual alternator battery light circuit. P1108 is stored when the ECU sees signal too high on manifold pressure sensor. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Ford codes:

P1108 on Honda

On Honda vehicles P1108 is documented as: Barometric pressure, barometric pressure sensor circuit, high voltage. P1108 is stored when the ECU sees signal too high on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Honda codes:

P1108 on Isuzu

On Isuzu vehicles P1108 is documented as: Barometric pressure circuit high input. P1108 is stored when the ECU sees signal too high on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Isuzu codes:

P1108 on Jaguar

On Jaguar vehicles P1108 is documented as: Manifold absolute pressure sensor high input. P1108 is stored when the ECU sees signal too high on manifold pressure sensor. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Jaguar codes:

P1108 on Mazda

On Mazda vehicles P1108 is documented as: Dual alternator battery light circuit. P1108 points at charging system. The standard definition names the system involved; which part inside it has actually failed is what the checks below establish, cheapest first.

Related Mazda codes:

P1108 on Peugeot

On Peugeot vehicles P1108 is documented as: Adaptation air inlet fault. P1108 is stored when the ECU sees malfunction on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Peugeot codes:

P1108 on Saab

On Saab vehicles P1108 is documented as: Charge air absolute pressure sensor, short circuit to positive. P1108 is stored when the ECU sees short to positive on turbocharger or boost control. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Signal wire touching a permanently live wire in a damaged loom; Connector pins bridged by corrosion or a bent terminal; Internal fault in the component shorting the signal to supply; Incorrect wiring after an aftermarket accessory was fitted.

Check first, cheapest first:

1. Disconnect the component and check whether the signal line still reads battery voltage
2. Inspect the loom for melted or rubbed insulation, especially near heat sources
3. Check the connector for a pushed-back or bent terminal
4. Trace the signal wire back to the module, looking for a live wire running alongside
5. Repair the harness, or replace the component if it is shorting internally

Related Saab codes:

P1108 on SsangYong

On SsangYong vehicles P1108 is documented as: Barometric pressure sensor.

Related SsangYong codes:

P1108 on Subaru

On Subaru vehicles P1108 is documented as: Variable inlet solenoid circuit (low). P1108 is stored when the ECU sees signal too low on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Subaru codes:

P1108 on Suzuki

On Suzuki vehicles P1108 is documented as: Radiator fan high speed circuit, manifold absolute pressure sensor rationality, signal too strong. P1108 is stored when the ECU sees signal too high on manifold pressure sensor. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Suzuki codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

P1xxx is manufacturer-specific code (VW/Audi, BMW, Mercedes, Toyota etc. have different meanings for the same code number).

Severity

Manufacturer-specific codes need a brand scanner (VCDS for VAG, INPA for BMW, STAR for Mercedes).

That is what holds for P1108 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.