B1855 — 3 documented meanings by make

B1855 does not mean the same thing on every car — manufacturers reuse the number for different faults. 4 makes document it: Chrysler, Ford, Mazda, Saab. Find your make below.

B1855 on Chrysler

On Chrysler vehicles B1855 is documented as: Driver's window motor control circuit high. B1855 is stored when the ECU sees signal too high on door / window / lock. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Open ground for the sensor, letting the signal float up; Signal line shorted to a supply voltage; Sensor failed open, which the module reads as maximum; Connector fault interrupting the return path.

Check first, cheapest first:

1. Read the live value and compare with what the conditions should produce
2. Check the sensor ground continuity back to the module
3. Unplug the sensor: if the reading changes, the wiring is intact and the sensor is suspect
4. Inspect the connector for corrosion or a spread terminal
5. Replace the sensor once ground and signal wiring are confirmed good

Related Chrysler codes:

B1855 on Ford, Mazda

On Ford, Mazda vehicles B1855 is documented as: Climate control air temperature internal sensor motor, short circuit to positive. B1855 is stored when the ECU sees short to positive on air conditioning / climate. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Signal wire touching a permanently live wire in a damaged loom; Connector pins bridged by corrosion or a bent terminal; Internal fault in the component shorting the signal to supply; Incorrect wiring after an aftermarket accessory was fitted.

Check first, cheapest first:

1. Disconnect the component and check whether the signal line still reads battery voltage
2. Inspect the loom for melted or rubbed insulation, especially near heat sources
3. Check the connector for a pushed-back or bent terminal
4. Trace the signal wire back to the module, looking for a live wire running alongside
5. Repair the harness, or replace the component if it is shorting internally

Related Ford, Mazda codes:

B1855 on Saab

On Saab vehicles B1855 is documented as: Relay 5, number 5 bow latch relay, internal fault. B1855 is stored when the ECU sees malfunction on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring or connector fault in the circuit; Component failed electrically; Supply or ground problem feeding the circuit; Controlling module fault, though this is the least common of the four.

Check first, cheapest first:

1. Read all stored codes — a general fault code is often the symptom of a more specific one
2. Inspect the connector and wiring for the named component
3. Check supply and ground at the component
4. Measure the component against specification
5. Replace the component once wiring and supply are ruled out

Related Saab codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

B1xxx is body systems, manufacturer-specific.

Severity

Manufacturer-specific body system — needs a brand scanner to read the actual cause.

That is what holds for B1855 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.