B1395 — 6 documented meanings by make

B1395 does not mean the same thing on every car — manufacturers reuse the number for different faults. 7 makes document it: Chevrolet (Daewoo), Ford, Hyundai, Kia, Mazda, Opel / Vauxhall, Saab. Find your make below.

B1395 on Chevrolet (Daewoo), Hyundai

On Chevrolet (Daewoo), Hyundai vehicles B1395 is documented as: Firing loop interconnection.

Related Chevrolet (Daewoo), Hyundai codes:

B1395 on Ford, Mazda

On Ford, Mazda vehicles B1395 is documented as: Power door memory lock relay, short circuit to ground. B1395 is stored when the ECU sees short to ground on door / window / lock. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring insulation chafed through where the loom passes a bracket or edge; Water or salt in a connector bridging the signal pin to the body; The component itself shorted internally; A harness pinched during earlier repair work.

Check first, cheapest first:

1. Unplug the component and re-read the code — if it changes, the fault is in the component, not the wiring
2. Inspect the loom where it passes metal edges, brackets and hinges
3. Open the connector and check for green corrosion or moisture
4. Measure resistance from the signal pin to a body ground; near-zero confirms the short
5. Repair the harness section, or replace the component if it shorted internally

Related Ford, Mazda codes:

B1395 on Kia

On Kia vehicles B1395 is documented as: Squib interconnection. B1395 points at airbag / restraint system. The standard definition names the system involved; which part inside it has actually failed is what the checks below establish, cheapest first.

Related Kia codes:

B1395 on Opel / Vauxhall

On Opel / Vauxhall vehicles B1395 is documented as: Engine running signal, low voltage; Driver's door approach sensor supply voltage circuit, high/low voltage. B1395 is stored when the ECU sees signal too low on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: High resistance in the supply or ground path, dragging the signal down; Corroded connector adding resistance the module reads as a low reading; Sensor drifted out of tolerance with age; Partial short to ground somewhere in the signal line.

Check first, cheapest first:

1. Read the live value on a scanner and compare with a known-good reading
2. Clean and re-seat the connector, then re-test before replacing anything
3. Check the ground point for that circuit — a poor ground causes this far more often than a bad sensor
4. Measure the sensor against specification with the connector back-probed
5. Replace the sensor only once the wiring and ground have been ruled out

Related Opel / Vauxhall codes:

B1395 on Saab

On Saab vehicles B1395 is documented as: Position sensors feed, short circuit to ground. B1395 is stored when the ECU sees short to ground on the circuit named in the code. That describes how the circuit is behaving, not which part has failed — the wiring, the connector and the component itself can all produce it, which is why the checks below start with the cheapest.

Usually one of: Wiring insulation chafed through where the loom passes a bracket or edge; Water or salt in a connector bridging the signal pin to the body; The component itself shorted internally; A harness pinched during earlier repair work.

Check first, cheapest first:

1. Unplug the component and re-read the code — if it changes, the fault is in the component, not the wiring
2. Inspect the loom where it passes metal edges, brackets and hinges
3. Open the connector and check for green corrosion or moisture
4. Measure resistance from the signal pin to a body ground; near-zero confirms the short
5. Repair the harness section, or replace the component if it shorted internally

Related Saab codes:

Which one is yours

A generic OBD reader gives you the number, not which of these meanings your manufacturer assigned to it. To get to the specific one:

1. Use a brand-specific scanner — VCDS for VAG, INPA or ISTA for BMW, XENTRY for Mercedes, Forscan for Ford. It shows the manufacturer's own text rather than the generic one.
2. Read all stored codes together — the neighbouring ones usually point at which system is involved and narrow the list.
3. Check freeze-frame data: the RPM, temperature and load at the moment it triggered indicate which system was active.
4. If you have no brand scanner, tell me the make and model below and I will tell you which of these applies to your car.

Code family

B1xxx is body systems, manufacturer-specific.

Severity

Manufacturer-specific body system — needs a brand scanner to read the actual cause.

That is what holds for B1395 in general. From here it depends on your engine — tell me which car it is and what it does, and I will give you the steps for it: real procedures, torque figures and diagrams instead of general advice.