F8Q-630 engine — Renault 1.9 dCi (1.9L)
1.9L · 64 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | F8Q-630 |
| Capacity | 1870 cc |
| Idle speed | 850 ± 50 rpm |
| Inlet | 0.20 mm |
| Exhaust | 0.40 mm |
| Oil pressure | 1.2 / 1000 3.5 / 3000 bar/rpm |
Engine (diesel)
| System (make and type) | LUCAS DPCN |
| Injection pump (make and type) | LUCAS 8448B/190A |
| Injector (make and type) | LUCAS RDN OSDC 6902 |
| Number of cylinders | 4 |
| Injector firing order | 1 - 3 - 4 - 2 |
| Injector pressure | 130 ± 5 bar |
| Max. no-load governed speed | 4600 ± 100 rpm |
| Exhaust gas analysis (opacity) | 64 % |
| Exhaust gas analysis | 2.35 m-1 |
Cooling system
| Cap pressure | 1.2 bar |
| Thermostat opens at | 89 - 101 °C |
Electrical
| Battery | 70 Ah |
| Alternator | 75 A |
| Alternator | 110 A |
Capacities
| Engine sump, incl. filter | 5.2 l |
| Manual transmission | JB1 |
| Gearbox refill | 3.4 l |
| Cooling system | 7.4 l |
| Air-conditioner refrigerant | 660 ± 35 g |
| Air-conditioner compressor oil | 135 ± 10 ml |
Torque settings
| Cylinder head bolts — Stage 1 | 30 Nm |
| Cylinder head bolts — Stage 2 | 100 ± 4 ° |
| Cylinder head bolts — Stage 5 | 25 Nm |
| Cylinder head bolts — Stage 6 | 213 ± 7 ° |
| Repeat stages 4, 5 and 6 for bolts: | 3-4, 5-6, 7-8, 9-10 |
| Valve cover | 12 Nm |
| Camshaft bearing caps | Ø 6 mm : 10 Ø 8 mm : 20 Nm |
| Injector nozzle | 70 Nm |
| Glow plugs | 20 Nm |
| Inlet manifold | 25 Nm |
| Exhaust manifold | 25 Nm |
| Big-end bearing cap — Stage 1 | 20 Nm |
| Big-end bearing cap — Stage 2 | 40 ° |
| Main bearing cap | 60-65 Nm |
| Wheel bolts | 90 (-> 2003) 110 (2003 ->) Nm |
| Front hub | 280 Nm |
| Rear hub | 175 Nm |
Emissions
| Emission code | 70/220*1996/69 |
| Emission standard | Euro 2 (10/1997 ->) |
| CO2 average | 180 - 194 g/km |
| CO | 0.353 - 0.471 g/km |
| NOx | 0.460 g/km |
| HC NOx | 0.494 - 0.519 g/km |
| Particles | 0.047 - 0.048 g/km |
| Emission code | 70/220*1998/69 |
| Emission standard | Euro 2 (07/1999 ->) |
| CO2 average | 181 g/km |
| CO | 0.353 g/km |
| HC NOx | 0.494 g/km |
| Particles | 0.048 g/km |
| Emission code | 70/220*1998/69A |
| Emission standard | Euro 3 (08/2000 ->) |
| Emission code | 70/220*1999/102A |
| Emission standard | Euro 3 (10/2000 ->) |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a F8Q-630 problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.