D24TIC engine — Volvo 2.4 D (2.4L)
2.4L · 122 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | D24TIC |
| Capacity | 2383 cc |
| Idle speed | 830 rpm |
| Inlet | 0.20 mm |
| Exhaust | 0.40 mm |
| Normal | 32 bar |
| Minimum | 24 bar |
| Oil pressure | 2/2000 bar/rpm |
| Engine code | D 24 TIC |
| Idle speed | 830 ± 50 rpm |
| Valve clearance | (-> 1993) |
| Inlet | 0.15 - 0.25 mm |
| Exhaust | 0.35 - 0.45 mm |
| Valve clearance | (1993 ->) |
| Normal | 32.0 bar |
| Minimum | 24.0 bar |
| Differential limit between cylinders | < 0.8 bar |
| Oil pressure | 2.0/2000 bar/rpm |
Engine (diesel)
| Injection pump (make and type) | Bosch VE6/10F 2400 TIC2 |
| Number of cylinders | 6 |
| Injector firing order | 1-5-3-6-2-4 |
| Injection pump timing (static) | 0.90 mm |
| Injector pressure | 155 - 163 bar |
| Exhaust gas analysis (opacity) | 73 % |
| Exhaust gas analysis | 3.00 m-1 |
| Max. no-load governed speed | 5400 rpm |
| Oil temperature during test | 60 °C |
| Injection pump (make and type) | Bosch VE6/10F2400 TIC2 (-> 1993) Bosch VE6/10F2400 L116-7 (1993 ->) |
| Injection pump (make and type) | Bosch VE6/10F2400 TIC2-1 (-> 1993) Bosch VE6/10F2400 L116-8 (1993 ->) |
| Injection pump timing (static) | 0.90 (-> 1993) 0.95 (1993 ->) mm |
| Injector (make and type) | Bosch KCA 30 S 36/4 |
| Injector pressure | 163 bar |
| Minimum | 155 bar |
| Exhaust gas analysis test method/probe (Germany only) | B / 1 |
Cooling system
| Cap pressure | 1.5 bar |
| Thermostat opens at | 87 - 102 °C |
Electrical
| Battery | 90 Ah |
| Alternator | 80 A |
Capacities
| Engine sump, incl. filter | 6.0 l |
| Gearbox refill | 2.3/1.6 l |
| Differential | 1.6 l |
| Gearbox refill | 2.0 l |
| Cooling system | 11.5 l |
Torque settings
| Cylinder head bolts — Stage 1 | 40 Nm |
| Cylinder head bolts — Stage 2 | 60 Nm |
| Cylinder head bolts — Stage 3 | 75 Nm |
| Cylinder head bolts — Stage 4 | 180 ° |
| Cylinder head bolts — Stage 5 | T = 85 °C |
| Cylinder head bolts — Stage 6 | 90 ° |
| Cylinder head bolts — Stage 8 | 90 |
| Cylinder head bolts — Stage 1 | 100 Nm |
| Cylinder head bolts — Stage 2 | 45 ° |
| Wheel nuts | 85 Nm |
| Injector nozzle | 70 Nm |
| Glow plugs | 22 Nm |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a D24TIC problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.