D16Y3 engine — MA 1.6 (1.6L)
1.6L · 113 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | D16 |
| Capacity | 1590 cc |
| Idle speed | 750 ± 50 rpm |
| Inlet | 0.18 - 0.22 mm |
| Exhaust | 0.23 - 0.27 mm |
| Oil pressure | 1.4 bar/rpm |
| Engine code | D16Y3 |
| Normal | 12.7 bar |
| Minimum | 9.3 bar |
| Differential limit between cylinders | < 2.0 bar |
| Oil pressure | 0.7 / 750 3.4 / 3000 bar/rpm |
Engine (petrol)
| Fuel system (make and type) | Honda PGM-Fi |
| Number of cylinders | 4 |
| Firing order | 1 - 3 - 4 - 2 |
| Timing stroboscopic (before TDC) | 16 ± 2 °/rpm |
| Ignition coil resistance, primary | 0.71 - 0.81 ohms |
| Spark plugs (make and type) | Unipart GSP5658 |
| Spark plug gap | 1.0 mm |
| Fuel pump pressure | 4.1 bar |
| Injection pressure/system pressure | 2.5 bar |
| CO exhaust gas | < 0.4 % |
| CO2 | 14.5 - 16.0 % |
| HC | < 100 ppm |
| O2 | 0.1 - 0.5 % |
| Lambda | 0.98 - 1.02 |
| Lambda change (Delta Lambda) | 0.02 |
| Oil temperature during test | 70 °C |
| Fast-idle speed | 2500 - 2800 rpm |
| CO at fast-idle speed | < 0.25 % |
| Closed-loop test at: | 700 - 1100 rpm |
| Firing order | 1-3-4-2 |
| Timing stroboscopic (before TDC) | 16 ± 2 / 750 °/rpm |
| Ignition coil resistance, primary | 0.6 - 0.8 ohms |
| Ignition coil resistance, secondary | 13000 - 19000 ohms |
| Spark plugs (make and type) | NGK BKR6E-11 |
| Spark plugs (make and type) | NGK BKR7E-11 |
| Spark plug gap | 1.0 - 1.1 mm |
| Injection pressure/system pressure | 2.8 - 3.2 bar |
| CO exhaust gas | < 0.1 % |
| CO2 | > 14 % |
| Lambda | 0.97 - 1.03 |
| Fast-idle speed | 2300 - 2700 rpm |
| CO at fast-idle speed | < 0.3 % |
| Oil temperature during test | 80 °C |
| Closed-loop test at: | 600 - 1000 rpm |
| Alternative method (Germany only) | 2 |
Cooling system
| Cap pressure | 1.0 - 1.3 bar |
| Thermostat opens at | 76 - 80 °C |
| Fan on at | 91 - 95 °C |
| Cap pressure | 0.95 - 1.25 bar |
Electrical
| Battery | 36 Ah |
| Alternator | 75 A |
Capacities
| Engine sump, incl. filter | 3.3 l |
| Manual transmission | 5C 37 WUH |
| Gearbox refill | 1.8 l |
| Automatic transmission | S1LA |
| Gearbox refill | 2.7 l |
| Gearbox refill after overhaul | 5.9 l |
| Cooling system | 4.4 l |
| Air-conditioner refrigerant | 615 - 665 g |
| Air-conditioner compressor oil | 135 ml |
Torque settings
| Cylinder head bolts — Stage 1 | 30 Nm |
| Cylinder head bolts — Stage 2 | 65 Nm |
| Front hub | 181 Nm |
| Rear hub | 181 Nm |
| Wheel nuts | 98 - 118 Nm |
| Spark plugs | 18 Nm |
Emissions
| Emission code | 70/220*1996/69 |
| Emission standard | Euro 2 |
| CO2 average | 212 g/km |
| CO | 1.020 - 1.024 g/km |
| HC | 0.129 g/km |
| NOx | 0.089 g/km |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a D16Y3 problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.