B200K engine — Volvo 2.0 (2L)
2L · 101-106 hp
Engine overview
Vehicles with this engine
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | B200K |
| Capacity | 1990 cc |
| Idle speed | 900 rpm |
| Inlet | 0.35 - 0.45 mm |
| Exhaust | 0.35 - 0.45 mm |
| Normal | 9 - 11 bar |
| Oil pressure | 2.5 - 6.0/2000 bar/rpm |
| Capacity | 1986 cc |
| Inlet | 0.35 - 0.40 mm |
| Exhaust | 0.35 - 0.40 mm |
| Normal | 8.8 bar |
Engine (petrol)
| Fuel system (make and type) | Solex CISAC |
| Number of cylinders | 4 |
| Firing order | 1-3-4-2 |
| Timing stroboscopic (before TDC) | 7/750 °/rpm |
| Start | 0 - 2/1000 °/rpm |
| End | 18 - 23/3200 °/rpm |
| Ignition coil resistance, primary | 0.6 - 0.8 ohms |
| Ignition coil resistance, secondary | 6900 - 8500 ohms |
| Spark plugs (make and type) | Bosch WR6DC |
| Spark plug gap | 0.75 mm |
| Fuel pump pressure | 0.15 - 0.27 bar |
| CO exhaust gas | 1.0 - 2.5 % |
| CO2 | 13 - 16 % |
| HC | 30 ppm |
| O2 | 0.5 - 2.0 % |
| Timing stroboscopic (before TDC) | 15/750 °/rpm |
| Spark plugs (make and type) | ( -1987): Bosch W7DC (1988 -): Bosch WR7DC |
| Spark plug gap | 0.7 - 0.8 mm |
| CO exhaust gas | 0.5 - 2.0 % |
| HC | 300 ppm |
Cooling system
| Cap pressure | 0.75 - 0.85 bar |
| Thermostat opens at | 87 - 97 / 92 - 102 °C |
| Cap pressure | 1.0 bar |
| Thermostat opens at | 87 - 102 °C |
Electrical
| Battery | 64 Ah |
| Alternator | 70 A |
| Battery | 44 Ah |
| Alternator | 64 A |
Capacities
| Engine sump, incl. filter | 3.9 l |
| Gearbox refill | M40: 0.8 M45: 0.8 M41: 1.6 M46: 2.3 M47 (- 1987): 1.3 M47 (1987 -): 1.6 l |
| Differential | 1.6 l |
| Gearbox refill | 7.4 l |
| Cooling system | 9.5 l |
| Engine sump, incl. filter | 3.85 l |
| Gearbox refill | 2.6/1.6 l |
| Gearbox refill | 3.9 ZF: 2.0 l |
| Cooling system | 8.5 l |
Torque settings
| Cylinder head bolts — Stage 1 | 60 Nm |
| Cylinder head bolts — Stage 2 | 110 Nm |
| Cylinder head bolts — Stage 3 | T = 80°C |
| Cylinder head bolts — Stage 4 | t = 30 min |
| Cylinder head bolts — Stage 5 | -90° ° |
| Cylinder head bolts — Stage 6 | 110 Nm |
| Cylinder head bolts — Stage 1 | 20 Nm |
| Cylinder head bolts — Stage 2 | 60 Nm |
| Cylinder head bolts — Stage 3 | +90° ° |
| Wheel nuts | 100 - 130 Nm |
| Spark plugs | 25 ± 5 Nm |
| Cylinder head bolts — Stage 3 | 90 ° |
| Cylinder head bolts — Stage 1 | 100 Nm |
| Cylinder head bolts — Stage 2 | 45 ° |
| Wheel nuts | 85 Nm |
| Spark plugs | 25 Nm |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a B200K problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.