B18FP engine — Volvo 1.7 (1.7L)
1.7L · 102 hp
Engine overview
Factory specifications
Values from the manufacturer documentation for this engine.
Engine (general)
| Engine code | B 18 FP |
| Capacity | 1721 cc |
| Idle speed | 850 - 950 rpm |
| Inlet | 0.20 ± 0.05 mm |
| Exhaust | 0.40 ± 0.05 mm |
| Normal | 11 - 13 bar |
| Oil pressure | 2/1000 3.5/3000 bar/rpm |
| Engine code | B18FP |
Engine (petrol)
| Fuel system (make and type) | Fenix 3B |
| Number of cylinders | 4 |
| Firing order | 1-3-4-2 |
| Timing stroboscopic (before TDC) | 8 ± 3/900 °/rpm |
| Ignition coil resistance, primary | 0.5-1.5 ohms |
| Ignition coil resistance, secondary | 5500-6500 ohms |
| Spark plugs (make and type) | Bosch WR6DC |
| Spark plug gap | 0.7 mm |
| Fuel pump pressure | 3.0-3.2 bar |
| Injection pressure/system pressure | 3.5 bar |
| CO exhaust gas | < 0.5 % |
| CO2 | 14.5 - 16.0 % |
| HC | 100 ppm |
| O2 | 0.1 - 0.5 % |
| Lambda | 0.97 - 1.03 |
| Oil temperature during test | 70 °C |
| Fast-idle speed | 2400 - 2600 rpm |
| CO at fast-idle speed | < 0.3 % |
| Lambda change (Delta Lambda) | 0.03 |
| Conditioning catalytic converter | 2 / 3000 min/rpm |
| Injection pressure/system pressure | 3.0-3.2 bar |
Cooling system
| Cap pressure | 1.5 bar |
| Thermostat opens at | 92 °C |
| Stage 1/Fan 1 | 95 °C |
| Stage 2/Fan 2 | 101 °C |
Electrical
| Battery | 55 Ah |
| Alternator | 60 A |
| Alternator | 70 A |
Capacities
| Engine sump, incl. filter | 5.3 (-> 1993) 5.0 (1993) 4.6 (1994->) l |
| Gearbox refill | 3.4 l |
| Automatic transmission | ZF 4 HP 14 Q |
| Gearbox refill | 3.3 l |
| Cooling system | 6.5 l |
| Engine sump, incl. filter | (- 1992): 5.3 (1993): 5.0 (1994 -): 4.6 l |
Torque settings
| Cylinder head bolts — Stage 1 | 30 Nm |
| Cylinder head bolts — Stage 2 | 70 Nm |
| Cylinder head bolts — Stage 5 | 20 Nm |
| Cylinder head bolts — Stage 6 | 123 ± 2 ° |
| Front hub | 230 Nm |
| Rear hub | 220 (->1990) Nm |
| Rear hub | 160 (1990->) Nm |
| Wheel nuts | 110 Nm |
| Spark plugs | 25 Nm |
| Cylinder head bolts — Stage 4 | 360 ° |
| Cylinder head bolts — Stage 6 | 125 ° |
| Rear hub | 160 Nm |
Workshop procedures for this engine
Step-by-step procedures from the workshop database.
Got a B18FP problem? Ask for free.
Describe the symptoms — TorqFix replies with a diagnosis cited from verified workshop data.
Get free diagnosis →Who makes these pages, and how
TorqFix was built by a mechanic — after a 2,700 km drive with five roadside repairs that no diagnostic tool could explain.
The figures on this page come from manufacturer workshop documentation and are shown as they are. The page is assembled automatically from that data — it is not written by an AI. The AI works in the chat, where it answers for your specific car. It writes nothing here.
Variants of the same model differ. Cross-check torque against the factory manual for your engine before final tightening.
Seen a figure that does not match your manual? Write to us — we correct it and note when. support@torqfix.com
The story behind TorqFix →Workshop data on this page last updated 22 Aug 2026.